LM R e Thin Film Resistor Network. 0 05% Matching and 5 ppm This datasheet has been download from: Datasheets for electronics components. On all operational amplifier data sheets, the specifications listed on the deep in the data sheet. .. , LM and LT with improved price/performance. LM Datasheet: LM Precision Operational Amplifier, LM PDF Download National ->Texas Instruments, LM Datasheet PDF, Pinouts, Data Sheet.

Author: Arashinris Yorn
Country: Swaziland
Language: English (Spanish)
Genre: Career
Published (Last): 22 November 2015
Pages: 106
PDF File Size: 10.61 Mb
ePub File Size: 11.51 Mb
ISBN: 438-8-32937-520-6
Downloads: 82590
Price: Free* [*Free Regsitration Required]
Uploader: Kekinos

Consult factory for availability of devices with Guaranteed Long-term Stability. The LM also provides excellent stability vs. To avoid this transient, it may be advisable to preload the output with a few milliamperes of load to ground. The capacitor used should be a low-leakage type. Changes in output voltage due to heating effects are covered under the specifications for Thermal Regulation and Tempco.

The device does l607 include a thermal shut-down circuit. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness.

These pins may be cut off if desired. Avoid such overloads for voltages higher than a 20 V, for more than 5 seconds, or, at high ambient temperatures.

LM Datasheet PDF – National Semiconductor

For example, if the output were trimmed up to The LM has a Class B output, and will exhibit transients at the crossover point. Life support devices or systems are devices or systems which, a are intended for surgical implant into the body, or b support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user.


Unless otherwise noted, these conditions apply: Alternatively, a shield foil can be laid out on the printed circuit board, surrounding these pins and pin 5, and this guard foil can be connected to ground or to Vout, effectively acting as a guard against AC coupling and DC leakages.

These pins would not be damaged by a short to ground, or by Electrostatic Discharges; however, keep them away from large transients or AC signals, as stray capacitance could couple noises into the output. Do not connect anything to these pins, or improper operation may result. A military Lm60 electrical test specification is available on request. Ceramic capacitors may seem to do datashest job, but are not recommended for production use, as the high-K ceramics cannot be guaranteed for low leakage, and may exhibit piezo-electric effects, converting ,m607 or mechanical stress into excessive electrical noise.

Contact the factory for availability of devices with proven long-term stability. In Sinking mode, connect 0. Trimming to a wider range is possible, but is not recommended as it may degrade the Tempco and the Tempco linearity at temperature extremes. The devices have a The output has a class-B stage, so if the load current changes from sourcing to sinking, an output transient will occur. If the output is pulled to a positive voltage such as a 15 or a 20V, the output current will be limited, but overheating may occur.

There is no guarantee that the Specified Temperatures are exactly at the minimum or maximum deviation. This datasheet has been downloaded from: LM see curve above: The LM is recommended for applications where the highest stability lm670 lowest noise is required over the full military temperature range.

The LM is suitable for limited-temperature dtasheet. The trim scheme is such that individual resistors are cut open rather than being trimmed partially cutto avoid resistor drift caused by electromigration in the trimmed area. The trim pin pin 5 should also be guarded away from noise signals and leakages, as it has a sensitivity of 15 millivolts of DVout per microampere.


Documents Flashcards Grammar checker. Regulation is measured at constant temperature using pulse testing with a low duty cycle.

LM607 Datasheet PDF

Capacitance in vatasheet Typical Performance Characteristics section show graphically that a modest capacitance of 0. They are based on a buried zener datasheeet as pioneered in the LM references, but do not require any heater, as they rely on special temperature-compensation techniques Patent Pending. National Semiconductor Europe Fax: A trim pin is available which permits fine-trimming of Vout, and also permits filtering to greatly decrease the output noise by adding a small capacitor 0.

The curves showing the Noise vs. This point occurs when the device is required to sink approximately 1. Its long-term stability is typically 3 to 10 ppm per hours when held near Tmax, and slightly better when operated at room temperature. Pin numbers for H, M or N packages. In some applications it may be advantageous to pre-load the output to either Vin or to ground, ml607 avoid this crossover point.

However, avoid overloads at high ambient temperatures, as a prolonged short-circuit may cause the junction temperature to exceed the Absolute Maximum Temperature. Thermal regulation is defined as the change in the output voltage at a time T after a datashdet change of power dissipation of mW. The output can sink current as well as source it, but the output impedance is much better for sourcing current. Consult factory for availability of devices with tighter Accuracy and Tempco Specifications.