Find great deals for 2 Sanyo STKII Stereo Amplifier Module Factory Sony. Shop with confidence on eBay!. Electronic component datasheet for STKII manufacturer Sanyo. Free doqnload!. The STKII series (STKII) and STKV series (high-grade type) are pin-compatible in the output range to 50W and enable easy design. Small-sized.
|Published (Last):||3 May 2012|
|PDF File Size:||13.5 Mb|
|ePub File Size:||12.46 Mb|
|Price:||Free* [*Free Regsitration Required]|
It incorporates high value emitter ballast resistors, gold More information.
Low noise quad operational amplifier. C monolithic integrated circuit.
Zero Voltage Switch with Fixed Ramp. IF amplifier, quadrature detector, AF preamplifier, signal meter, tuning indicator drive output. It was designed for the best. This is advanced information on a new product now in development or undergoing evaluation. Description Three-terminal adjustable negative voltage regulators Datasheet – production data current limit, thermal overload protection and safe area protection.
Typically it provides 22W output power More information. Full wave logic Pulse amplifier. It includes a microphone amplifier, voltage controlled oscillator More information.
By themselves, these devices. It is used to control resistive loads at mains. Due to reducing the number of external More information.
STK4152II AF Power Amplifier (Split Power Supply)
By itself, it will supply output currents up to ma. Minimum number of external parts required No input capacitor, bootstrap More information.
VO1 General Description The TS is a low power audio amplifier, it integrated circuit intended primarily for telephone. Description 4 x 46 W quad bridge car radio amplifier Datasheet production data Features High output power capability: General description The TDA89 is an high efficiency class-d audio power amplifier.
Bootstrap resistors The quiescent current is set by these resistors 2.
The LM is ideally suited for systems which. Three-terminal adjustable negative voltage regulators. The output noise voltage is represented by the peak value on rms scale VTVM of average value indicating type. Small pop noise at the time More information. With high unity gain frequency and a guaranteed. To reduce the pop noise at the time of application of power, it is effective to increase C3, C4 that fix the time constant on the input side and to decrease C5, C6 on the NF side.
These resistors fix voltage gain VG. Oscillation blocking capacitors Must be inserted as close to the IC power supply pins li possible so that the power supply impedance is decreased to operate the IC stably.
NEW ORIGINAL STK4152II STK4152 AF Power Amplifier (Split Power Supply)
Features Stj4152 current 1. It consists of four independent, high gain, internally compensated, low power operational amplifiers which have been designed to. These resistors fix the input impedance practically. Anyone purchasing any products described or contained herein for an above-mentioned use shall: Start display at page:. Pin Assignments V IN. The display level range is 9mVrms to mVrms Typ.
Total Harmonic More information.
STKII Price & Stock | DigiPart
st4152 In order to hold system cost to a minimum, gain is internally fixed at 34 db. Operating substrate temperature Condition 2: By themselves, these devices More information. A unique input More information. However, do not increase C5 more than needed because the pop noise level becomes higher at the time of application of power.
STKII AF Power Amplifier (Split Power Supply)
On-chip 2 channels permitting use in stereo and bridge amplifier More information. Low noise quad operational amplifier Datasheet production data Features Low voltage noise: Electrolytic capacitors are recommended for C9, C Bootstrap capacitors When the capacitor value is decreased, the distortion is liable to be higher at low frequencies.
Capacitor for ripple filter Capacitor ij the TRused ripple filter in the IC system C7 Oscillation blocking capacitor A polyester film capacitor, being excellent in temperature characteristic, frequency characteristic, is recommended for C7.
It offers not only. It offers the designer an economical solution More information. For power supply at the time of test, use a constant-voltage power supply unless otherwise specified. Zero Voltage Switch with Adjustable Ramp.