2N2905 PDF

Bipolar (BJT) Transistor PNP 40V mA mW Through Hole TO 2. Philips Semiconductors. Product specification. PNP switching transistors. 2N; 2NA. FEATURES. • High current (max. mA). • Low voltage ( max. The 2N from Multicomp is a through hole, silicon planar PNP low power bipolar transistors in TO metal can package. This are general purpose transistor.

Author: Mezile Vole
Country: Trinidad & Tobago
Language: English (Spanish)
Genre: Travel
Published (Last): 27 April 2008
Pages: 466
PDF File Size: 11.62 Mb
ePub File Size: 2.36 Mb
ISBN: 526-2-39455-452-3
Downloads: 72994
Price: Free* [*Free Regsitration Required]
Uploader: Faecage

Mar 11, 5. Not planning ahead for such contingincies might find you creating a whole new board.

2N2905 Datasheet, Equivalent, Cross Reference Search

Mar 11, 8. What you might consider doing is laying out your board so that you could put three or four of the T1’s in parallel, with fairly low-value resistors in series with the collectors and bases. The schematic works, but after a few minutes it stops working but works when power is disconnected then reconnected. Posted by clickman in forum: Jul 17, 2m2905, 1, Which battery to use?

They are rated for quite a bit more power than 2N’s and 2N’s. Mar 10, 1. Your name or email address: If the schematic is correct and all the wiring is correct, then why doesn’t it work? Mar 10, 3. If you clip and bend TO leads, you can stick them on a set of smt pads.

  LEY 22362 PDF

2N, Tube 2N; Röhre 2N ID, Transistor

2n2095 I’ve never had to pay a shipping charge from RS, only “schlepping charge”; aka the cost of getting there and back One has to inspect the transistors in the assortment, look up the datasheets, and test them. The RS resistors have proven to me to be highly stable in their values. I will 2j2905 it with the 2n I am using timers form Maxim.

Their 15 pack of PNP transistors is labeled as 2n, but they all have different codes written on them.

Interfaces for Computer-Controlled Test Systems A short introduction to some of the more popular interfaces used to connect test instruments to computers. I received the transistors and made a circuit board.

Look for the current carefully. Posted by picstudent in forum: Which SMT transistors to use? Expect resistance sic if you have soldered leads to it. No, create an account now.

Which Equation to use? You May Also Like: Thanks for the help! Try hooking up the right just like you have the left hooked up. Even though I had owned it for over 20 years, my local RS store exchanged it for a new one, no questions asked – it was obvious that it had not been installed.


If so, do you have the – terminals going towards the 0v from the controller? The 2N clearly says 2N, not “like” or “similar to” 2N It looks to me like the E and C connections to the right trigger may be reversed in the schematic. I made one mod with both triggers, then one that only used T2, then one that only used T1.

The transistors I have are sot, I have the correct wires going to the correct places on the transistors base, collector, emitter. Are they rated for at least 10v? I need SMT versions of 2n and 2n transistors.

Access Denied

If they are used as saturated 22n2905, though, this is not as large a problem as it would be if they were operating in the linear region. You generally get a selection of various transistors, and considering the overhead the store has, they’re actually a decent bargain.

Jan 18, 6, 1, Which multiplexor to use?

This does not include pots. The RS resistors have been extremely consistent in their values over the years.