74LS47 PDF

74LS47, 74LS47 Datasheet, 74LS47 pdf, buy 74LS47, 74LS47 BCD to 7- Segment Decoder. 74LS47 component details, pinout & Datasheet. 74LS47 is a BCD to 7-segment decoder/driver IC & It accepts a binary coded decimal as input and converts it. Texas Instruments 74LS47 Encoders, Decoders, Multiplexers & Demultiplexers are available at Mouser Electronics. Mouser offers inventory, pricing.

Author: Bamuro Kazisar
Country: Brunei Darussalam
Language: English (Spanish)
Genre: Finance
Published (Last): 10 September 2007
Pages: 448
PDF File Size: 16.51 Mb
ePub File Size: 4.73 Mb
ISBN: 908-4-55967-794-8
Downloads: 4669
Price: Free* [*Free Regsitration Required]
Uploader: Taukree

Access Denied

The B is very easy to use, and has only three input control terminals; of these, the not-LT pin 3 pin is normally tied high, but turns on all seven segments of the display when pulled low. Note in the cases of Figures 6 and 7 that an NPN buffer transistor must be interposed between each output drive segment and the input segment of the display. Basic way of using the B to drive a seven-segment common-cathode LED display.

If cascaded B ICs are required to give automatic leading-zero suppression, the basic Figure 17 circuit must be modified as shown in Figure 18 to provide ripple-blanking operation. Driving a gas discharge readout with a B. The not-BL pin 4 terminal is also normally tied high, but blanks turns off all seven segments when pulled low. The segment output currents are internally limited to about 5mA at 10V or 10mA at 15V.

74LS47 IC | 74LS47 Datasheet | Pin Diagram & Description

In each case, Rx determines the operating segment current of the display, and Ry determines the base current of the transistor. Basic method 74la47 cascading B ICs without zero suppression. In practice, however, it is far better to use a B IC for this particular application.

  CABOOLTURE LINE TRAIN TIMETABLE PDF

Figure 3 shows how to connect the ripple-blanking terminals to give leading zero suppression on the first three digits of a four-digit display.

Functional diagram and pin notations of the B decade counter with seven-segment display driver. Need to brush up on your electronics principles?

Learning Electronics Need to brush up on your electronics principles? Figures 6, 7and 8 show how to modify the above circuit to drive LED common-anode displays, gas discharge displays, and low-brightness fluorescent displays, respectively.

Using Seven-Segment Displays — Part 2 | Nuts & Volts Magazine

Figure 11 shows the basic way of using the B to drive a seven-segment LCD, and Figures 12 and 13 show it used to drive other types of seven-segment displays. A special two-part feature on 74ls74 to use seven-segment alphanumeric displays.

Finally, the LE latch enable terminal pin 5 enables the IC to give either direct or latched decoding operation. Driving a fluorescent readout with a B. Figure 4 shows the functional diagram and pin notations of the device, which can use any power source in the 5V to 15V range.

The CO signal is a symmetrical square- wave at one-tenth of the CLK input frequency, and is useful in cascading B counters. Method of applying leading-zero suppression to the first three digits of a four-digit display using 74LS47 ICs. 74lz47 multi-part series may be just what you need!

Enabling the display can be connected directly to the outputs of the IC without the use of external current-limiting resistors. The IC does not incorporate a data latch and has no facility for ripple blanking.

  LA PATRIA DEL CRIOLLO SEVERO MARTINEZ PELAEZ PDF

74LS47 7-Segment Decoder

If trailing-zero suppression is required, the direction of ripple-blanking feedback must be reversed with the RBI terminal of the LSD grounded and its RBO terminal wired to the RBI terminal of the next least-significant stage, and so on.

Some of these devices have integral ripple-blanking facilities, others have built-in data latches, and a few even have built-in decade counter stages, etc. Figure 1 shows the functional diagrams and pin designations of these devices, each of which is housed in a pin DIL package.

A current-limiting resistor Rx must be wired in series with each display segment and must have 74ks47 value chosen to limit the segment current below 25mA. Figure 14 shows the functional diagram and pin notations of the B.

Figure 15 shows the basic circuit connections to be used when cascading stages. The B has four input control terminals, and three auxiliary output terminals.

Series Using 7-Segment Displays All articles in this series: The B can be used to drive most popular types of seven-segment displays. This feature enables the IC to act as a universal unit that can drive common-cathode or common-anode LED or liquid-crystal seven-segment displays with equal ease, as shown in Figures 10 to