ASTM A/AM: Standard Specification for Electric-Resistance-Welded Metallic-Coated Carbon Steel Mechanical Tubing. A Mechanical Tubing. ASTM A includes steel grades from – Alro stocks A as welded mechanical tubing. A Tube includes a wide. Designation: A – Standard Specification for. Electric-Resistance-Welded Metallic-Coated Carbon Steel Mechanical Tubing1 This standard is issued.
|Published (Last):||10 May 2013|
|PDF File Size:||18.46 Mb|
|ePub File Size:||6.25 Mb|
|Price:||Free* [*Free Regsitration Required]|
It is informational only and not an official part of the standard; the full awtm of the standard itself must be referred to for its use and application.
We manufacture of ASTM A TYPE 1 Tubingis produced using aluminized steel which is carbon steel that has been pre-coated on both sides with an aluminum silicon alloy while in coil form. The steels shall conform to elemental tolerances for product analysis. The values stated in either SI units or inch-pound units are to be regarded separately as standard. Low-carbon steels and other carbon steels shall conform to the required chemical composition for carbon, manganese, phosphorus, and sulfur.
Sizes outside the ranges listed above may be ordered provided all other requirements of the specification are met.
A Mechanical Tubing | Alro Steel
Combining values from the two systems may result in non-conformance with the standard. A Type 6 Tubing provides a high degree of corrosion resistance and an excellent surface appearance and is a bridge between stainless and hot-dip galvanized finishes.
Carbon Steel A Tube Exporter. ASTM A Type 6 welded mechanical tubing is produced using steel that has been pre-coated with a thin layer of a zinc-aluminum-magnesium alloy coating while in coil form as specified in ASTM A ASTM A Type 3 welded a7787 tubing is produced out of a aetm rolled carbon steel and then is hot-dip galvanized per ASTM A specification into a tank of molten zinc after the tubing is already formed and welded.
ASTM A Tubing ,ASTM A Type 1,Type 2,Type 3,Type 4,Type 6,ASTM A | Superior Steel
Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Wall thickness tolerances for premetallic coated as-welded tubing and diameter tolerances for metallic-coated round tubing shall be provided. ASTM A Type 4 welded mechanical tubing is produced using carbon steel that has been pre-coated with a thin layer of zinc while in coil form and then heat treated to convert the coating into a zinc-iron alloy.
The values stated in either SI units or inch-pound units are to be regarded separately as standard. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.
This guide covers standard specification for round, square, rectangular, and special shape, electric-resistance-welded mechanical tubing, either zinc-coated galvanized a7787 welding or produced from aluminum-coated, zinc-coated galvanizedzinc-iron alloy-coated galvannealedor aluminum-zinc alloy-coated steel sheet. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
Outside Diameter Tange, in.
The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. This abstract is a brief summary of the referenced standard. This specification is expressed in both inch-pound units and in SI units; however, unless the purchase order specifies the applicable M specification designation SI unitsthe inch-pound units shall apply.
A787 Type 1, 2, 3, 4 & 6
Combining values from the two systems may result in non-conformance with the standard. Link to Active This link will always route to the current Active version of the standard.
Historical Version s – view previous versions of standard. Within the text, the SI units are shown in brackets.