ASTM B153 PDF

B – 11 Standard Test Method for Expansion (Pin Test) of Copper and Copper- Alloy Pipe and Tubing, copper, copper alloy, expansion, expansion test, pin. This standard is issued under the fixed designation B ; the 1 This test method is under the jurisdiction of ASTM Committee B05 on Copper. Find the most up-to-date version of ASTM B at Engineering

Author: Mezinos Kar
Country: Guinea-Bissau
Language: English (Spanish)
Genre: Software
Published (Last): 19 January 2013
Pages: 462
PDF File Size: 3.48 Mb
ePub File Size: 14.37 Mb
ISBN: 166-9-46097-976-6
Downloads: 34056
Price: Free* [*Free Regsitration Required]
Uploader: Malakora

Sampling for Visual and Dimensional Examination Standard Specification for Gray Iron Castings.

Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. A standard may be withdrawn with or without replacement.

This list is incomplete ; you can help by expanding it. For all other tube no Rockwell hardness values shall apply. Tubes for Voice and Pneumatic Service S5. The purchaser shall have the right to perform any of the inspections or tests set forth when such inspections and tests are deemed necessary to assure that the material conforms to prescribed requirements.

List of ASTM International standards – Wikipedia

Mercurous Nitrate Test Former soft anneal soft anneal light anneal light anneal soft anneal soft anneal light anneal light anneal soft anneal soft anneal up to 0. Immediately after removal from the solution, the specimen shall be wiped free of excess mercury and examined for cracks.

  APICIUS COOKERY AND DINING IN IMPERIAL ROME PDF

aatm Standard Specification for Steel Track Spikes. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. The notchdepth tolerance shall be Standard Specification for Ferromolybdenum. Dimensions and Permissible Variations Light-drawn bending temper is used only when a tube of some stiffness but yet capable of being bent is needed.

List of ASTM International standards

Tension tests are required for tubes with a wall thickness under 0. Limits for unnamed elements are to be established by agreement between manufacturer or supplier and purchaser.

Hard-drawn temper is used only where there is need for a tube as strong as is commercially feasible for the sizes indicated. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? A superscript epsilon e indicates an editorial change since the last revision or reapproval.

Standard designations usually consist of a letter prefix and a sequentially assigned number. Standard Specification for Ferrotitanium. This page was last edited on 30 Novemberat A withdrawn standard has been discontinued by its sponsoring committee. Retrieved August 29, Rockwell hardness tests shall be made on the inside surface of the tube.

  BSR14 PDF

Alternatively, if the manufacturer uses speed-insensitive eddy-current units that are equipped so that a fraction of the maximum unbalance signal is able to be selected, the following percent maximum unbalance signals shall be used. The manufacturer shall select the nondestructive test that is most suitable for the tube size and the application. B — 02 Standard Speci? Workmanship, Finish, and Appearance When there is a need for light-drawn or hard-drawn tempers these are to be supplied as agreed upon between the manufacturer and the atm.

If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. Xstm Size Pieces Per Satm Sample Size 2 to 8 9 to 90 91 to to to to to to 10 10 to 35 Entire lot 8 12 19 21 27 35 38 astmm Drawn temper is for general purposes and is most aatm used where there is no speci?

Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.