ASTM B Standard Specification for Aluminum and Aluminum-Alloy Bar, Rod, and Wire. ASTM B Standard Specification for Aluminum and Aluminum-Alloy Rolled or Cold Finished Bar, Rod, and Wire. (UNS A) is an aluminum bar with cold finished or extruded aluminum wrought product with excellent corrosion resistance, good workability, and.
|Published (Last):||11 June 2010|
|PDF File Size:||6.49 Mb|
|ePub File Size:||17.24 Mb|
|Price:||Free* [*Free Regsitration Required]|
Historical Version s – view previous versions of standard. Note 1—Throughout this specification use of the term alloy in the general sense includes aluminum as well as aluminum alloy.
6061 Aluminum Bar Stock
The producer may analyze samples for trace elements not specified in the specification. Join your peers on the Internet’s largest technical engineering professional community. The B is a spec for extruded bars, etc, and the B is a spec for cold-finished or cold rolled. Extruded bar is cheaper than cold-drawn bar. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.
It is informational only and not an official part of the standard; the full text of the standard itself must asstm referred to for its use and application. I would be more concerned about galvanic corrosion due to an Al nut being used on a stainless steel rod.
Aluminum ASTM B vs B – ASTM (testing materials) Code Issues – Eng-Tips
The products shall be produced either by hot extruding and cold finishing or by hot rolling with or without cold finishing. Note 2—The term cold finished is used to indicate the type of surface finish, sharpness of angles, and dimensional tolerances produced by drawing through a die. Active view current version of standard. It’s easy to join and it’s free. The application is for aluminum nuts on a threaded stainless steel rod so the nut is expected to strip before the rod.
Please first verify your email before subscribing to alerts. Add v211 Alert PDF. Are you an Engineering professional? C For purposes of determining conformance to these limits, an observed value or a calculated value obtained from analysis shall be aastm to the nearest unit in the last right-hand place of figures used in expressing the specified limit, in accordance with the rounding-off method of Practice E Note 3 See Specification B for aluminum and aluminum-alloy extruded bars, rods, wire, shapes, and g211 and Specification B for aluminum and aluminum-alloy rivet and cold-heading wire and asm.
Link to Active This link will always route n211 the current Active version of the standard. Need more than one copy? Posting Guidelines Promoting, selling, recruiting, coursework and thesis posting is forbidden.
However, such analysis is not required and may not cover all metallic Others elements. Such issues asfm the result of project complexity, size, uniqueness and regulation, as well as the need for virtual team collaboration. This specification covers rolled or cold-finished aluminum and aluminum-alloy bar, rod, and wire and includes the following UNS alloy designations: Please first log in with a verified email before subscribing to alerts.
ASTM B – 02 Standard Specification for Aluminum and Aluminum-Alloy Bar, Rod, and Wire
Subscription pricing is determined by: Bars, rods, and wires shall conform to the chemical composition requirements prescribed for aluminum, silicon, iron, copper, manganese, magnesium, chromium, zinc, bismuth, lead, and titanium, and to the specified tensile properties such as tensile strength, yield strength, and elongation.
You can download and open this file to your own computer but DRM prevents opening this file on another computer, including a networked server. The Eng-Tips staff will check this out and take appropriate action. Thank you for helping keep Eng-Tips Forums free from inappropriate posts. A Limits are in mass percent maximum unless otherwise shown.
G The aluminum content is the difference satm Note 1—Throughout this specification use of the term alloy in the general sense includes aluminum as well as aluminum alloy. If the document is revised or amended, you will be notified by email.
Close this window and log in. Note 2—The term cold finished is used to indicate the type of surface finish, sharpness of angles, and dimensional tolerances produced by drawing through a die. Should any analysis by the producer or the purchaser establish asm an Others element exceeds the limit of Each or that the aggregate astk several Others elements exceeds the limit of Totalthe material shall be considered non-conforming. Proceed to Checkout Continue Shopping.
Standards Subscriptions from ANSI provides a money-saving, multi-user solution for accessing standards. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are 2b11 provided as part of the standard.
Link to Active This link will always route to the current Active version of the standard. Can anyone tell me if there is any reason to be concerned with this substitution?