ASTM B571 PDF

ASTM B Standard Practice for Qualitative Adhesion Testing of Metallic Coatings. standard by ASTM International, 08/01/ View all product details. ASTM B quantifies various physical properties of metal coating substances such as gold, copper, silver and several others on their adhesion quality via. ASTM B STANDARD PRACTICE FOR QUALITATIVE ADHESION TESTING OF METALLIC COATINGS_建筑/土木_工程科技_专业资料。.

Author: Fesida Tubar
Country: Zambia
Language: English (Spanish)
Genre: Life
Published (Last): 2 January 2015
Pages: 38
PDF File Size: 10.77 Mb
ePub File Size: 1.9 Mb
ISBN: 274-9-84477-290-3
Downloads: 81880
Price: Free* [*Free Regsitration Required]
Uploader: Samujin

Heat curing of the adhesive may be used, keeping in mind considerations noted in 9. No b5711 units of measurement are included in this standard. This may be prying, hammering, bending, beating, heating, sawing, grinding, pulling, scribing, chiseling, or a combination of such treatments. Precision and Bias Reproducible results are more easily obtained by the use of a suitably modi?

ASTM B Adhesion Metals Coating Test Equipment

The pressure shall be sufficient to burnish the coating at each stroke but not so great as to dig into it. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every?

If permitted, test panels shall be of the same material and have the same surface? The adhesion of the coating may be observed directly or evaluated further by techniques described in Section 5 for detachment from the substrate.

Such adhesion is usually obtained if good electroplating practices are followed.

Soft or thin coatings cannot be evaluated for adhesion by this method. Examine asstm region at low magni? Make sure that any loose coating particles from scribing do not remain. No other units of measurement are included in this standard. Deposit continuous to the scribed lines is not considered.

  MANUAL 16F628 PDF

ASTM B571 Adhesion Metals Coating Test Equipment

The choice for each situation must be determined. Alternatively the chisel may be placed in back of an overhang area aetm the coating or at a coatingsubstrate interface exposed by sectioning the article with a saw. We offer machines, apparatus, testers, tensile grips, test fixtures, clamps, holders, jigs, faces, jaws, extensometers, environmental and humidity chambers, furnaces, baths and custom solutions for unique applications.

The adhesion is not adequate if the tape has deposit adhering to it that comes from the area between the scribed lines.

Blisters, lifting, or peeling should not develop. Vol 22,p. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.

If the coating peels, flakes, or lifts from the substrate, the adhesion is less than perfect. For example, an article that is to be subsequently formed would suggest a draw or a bend test; an article that is to be soldered or otherwise exposed to heat would suggest a heat-quench test. If it is possible to remove the deposit, the adhesion is not satisfactory. The tape shall be wide enough asm cover three or more parallel lines of the scribed area.

These tests have varying degrees of severity; and one might serve to distinguish between satisfactory and unsatisfactory adhesion in a speci? For reproducible results, the rate of pull, the thickness and width of the strip, and deposit thickness must be standardized.

Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

Then quench the part in water or other suitable liquid at room temperature. In many instances, the end use of the coated article or its method of fabrication will suggest the technique that best represents functional requirements.

  FREE TROLLBABE PDF

Coatings and substrates that are sensitive to oxidation should be heated in an inert or reducing atmosphere or a suitable liquid. In many instances, the end use of the coated article or its method of fabrication will suggest the technique that best represents functional requirements.

ASTM B – ADHESION OF PLATINGS (EXCEPT DRAW TEST)

A knife may be substituted for the chisel with or without hammering or light tapping. The severity of the test may be altered by changing the load and diameter of the ball.

This test is commonly used if the coating will peel without tearing. Rated to 10 kN 2, lbf Can be paired with adapters to yield non-perpendicular peels Maintains constant peel angle throughout the test. If the coating peels,? Originally approved in If more than one test is used, failure to pass any one test is considered unsatisfactory.

If a part requires baking or heat treating after plating, adhesion tests should be carried out after such posttreatment as well. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Last previous edition approved in as B — 97 Exfoliation or blisters in and around atm are evidence of inadequate adhesion.

This test practice is a simple set of tests to determine the adhesion of metallic coatings on various substances.

Posted in Sex