ASTM C1036 PDF

Flat Glass Inspection Criteria per ASTM C – 11/ASTM C Terminology. crush:lightly pitted condition with a dull gray appearance. dig:deep, short. Find the most up-to-date version of ASTM C at Engineering This standard is issued under the fixed designation C ; the number ASTM Standards: 2 cut size, n—glass ordered cut to its final intended size.

Author: Nesho Kigajar
Country: Burkina Faso
Language: English (Spanish)
Genre: Business
Published (Last): 9 July 2008
Pages: 214
PDF File Size: 12.10 Mb
ePub File Size: 12.3 Mb
ISBN: 966-3-83043-254-9
Downloads: 71035
Price: Free* [*Free Regsitration Required]
Uploader: Tojagar

Establishes the physical requirements for flat, heat strengthened, and fully tempered coated and uncoated glass. For linear dimensions of nonrectangular shapes, the length and width requirements in Table 2 shall be used.

Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. The values given in parentheses are for information only.

ASTM C – 16 Standard Specification for Flat Glass

Allowable blemishes per Table 3 PLUS three rejectable point blemishes Production of 1c036 glass products including coated, heat treated, laminated, and other select glass products. C103 number in parentheses indicates the year of last reapproval.

Place samples in the vertical position at the distance as speci? A superscript epsilon e indicates an editorial change since the last revision or reapproval. Discoloration and slight distortion of wire are permissible. Check with the manufacturer for thickness and dimensional tolerances on random Pattern P3 and special Pattern P4.

Flat Glass Inspection Criteria per ASTM C 1036 – 11/ASTM C 1048-12

Different test methods for Type I glass shall be performed in order to determine the following properties: The minimum separation distance between blemishes is determined by the minimum separation required for the asm of the two blemishes. Refer to Table 6 for evaluation criteria. Glass strength, overall bow, localized bow, dimension, hole, notches and cut-out tolerances and product labeling.

  HEART OF THE ENLIGHTENED ANTHONY DE MELLO PDF

C Within the 3.

Allowable blemishes for glass thicker than NOTE 4—Patterned glass can vary slightly in both con? Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.

F Allowed with a minimum separation of mm 24 in. Production of general use mirrors and other applications. For nonlinear dimensions of nonrectangular shapes, tolerances shall be as agreed upon by the involved parties.

None allowed None allowed Allowed Allowed with a minimum separation of mm 24 in. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. A None allowed None allowed None allowed See 6. Refer to Table 5 for evaluation criteria. Cookies are small files stored in your browser and are used by most websites to improve your overall experience.

Link to Active This link will always route to the current Active version of the standard. Measurements taken at any point shall meet the tolerance requirements of Table 7 or Table 8, or both.

Not allowed Q6 Quality 6 Allowed Allowed with a minimum ashm of mm 24 in.

This specification covers the quality requirements of flat, transparent, clear, and tinted glass. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every?

D Blemishes not speci? Applications in c10366 functional characteristics are a consideration and blemishes are not a major concern.

None allowed None allowed None allowed None allowed Allowed Allowed with a minimum separation of mm 24 in. Provides guidelines for categorizing and qualifying unintended visual obstructions in an IGU. F Allowed with a minimum asm of mm 48 in. Specifies the quality requirements for flat laminated glass consisting of two or more layers of glass bonded with an interlayer material. Opening 1c036 the mesh shall not exceed 16 mm 5?

  DL585 G7 QUICKSPECS PDF

This glass is intended to be used awtm for architectural glazing products including: Quality Quality-Q5 Typical Use Applications in which design and aesthetic characteristics are major considerations. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. If you feel that your comments have qstm received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.

Heavy mm 6 in. Edge seal durability, internal moisture formation, internal volatile fog formation, argon gas retention. Historical Version s – view previous versions of standard. If a blemish is detected, refer to Tables 3 and 4 for evaluation criteria. This abstract is a brief summary of the referenced standard. Type I which is a transparent flat glass and Type II which is a patterned and wired flat glass.

Place sample, with the direction of the draw oriented vertically, at a distance of approximately 4. This specification covers the quality requirements of flat, transparent, clear, and tinted glass intended wstm be used primarily for architectural c136 products. F Allowed with a minimum separation of mm 60 in.

Two types of glasses shall be used: