ASTM E8 E8M PDF

AHM E8/E8M – 13a. G–Gauge length. Dimensions, mm [in.] For Test Specimens with Gauge Length Four times the Diameter (E8]. Standard. Small-Size. Buy ASTM E 8/E8M: A TEST METHODS FOR TENSION TESTING OF METALLIC MATERIALS from SAI Global. Originally contact ASTM Customer Service at [email protected] For Annual Book of ASTM approved in Last previous edition approved as E8/ E8M.

Author: Fezahn Samubar
Country: Belize
Language: English (Spanish)
Genre: Spiritual
Published (Last): 12 August 2005
Pages: 24
PDF File Size: 9.15 Mb
ePub File Size: 20.17 Mb
ISBN: 682-1-36489-182-2
Downloads: 41820
Price: Free* [*Free Regsitration Required]
Uploader: Dousar

The values stated in each system are not exact equivalents; therefore each system must be used independently of the other. For proper gripping, it is desirable that the entire length of the serrated face of each wedge be in contact with the specimen.

Proper alignment of wedge grips and liners is illustrated in Fig. Brittle Materials—A schematic diagram of a gripping device for threaded-end specimens is shown in Fig. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

This error increases to 2. For this reason, a small taper is permitted in the reduced section of each atm the specimens described in the following sections. Such interpretation is usually applicable to values for reduction of area reported in the literature when no further qualification is given. For a standard This information may be useful in comparisons of materials, alloy development, quality control, and design under certain circumstances.

For measuring elongation at fracture with an appropriate extensometer, the gauge length of the extensometer sstm be equal to the nominal gauge length required for the specimen being tested. When liners are used behind the wedges, they must be of the same thickness and their faces must be flat and parallel. For best results, the wedges should be supported over their entire lengths by the heads of the testing machine.

  AISC S335 PDF

ASTM E8.E8M Tensiont testing of metallic materials –

These wedge grips generally furnish a satisfactory means of gripping long specimens of ductile metal. The test methods have been used extensively in the trade for this purpose. The forces used in determining tensile strength and yield strength shall be within the verified force application range of the testing machine as defined in Practices E4.

This em8 that liners of several thicknesses be available to cover the range of specimen thickness. Originally approved in C39M – 16 – Compressive Strength of Cylindrical Parte 1 de 8 Designation: It is important, therefore, that care be exercised in the preparation of specimens, particularly in the machining, to maximize precision and minimize bias in test results.

Astm a Astm a If, however, for any reason, one grip of a pair advances farther than the other as the grips tighten, an undesirable bending stress may be introduced. For short specimens and for specimens of many materials it is generally necessary to use machined test specimens and to astmm a special means of gripping to ensure that the specimens, when under load, shall be as nearly e8mm possible in uniformly distributed pure axial tension see 5.

No further reproductions authorized. A number in parentheses indicates the year of last reapproval. Both of these gripping devices should be attached to the heads of the testing machine through properly lubricated sphericalseated bearings.

  ASTM D3078 PDF

The gauge length is the most significant difference between E8 and E8M test specimens. To ensure axial tensile stress within the gauge length, the axis of the test specimen should coincide with the center line of the heads of the testing machine.

Current edition approved May 1, NOTE 3—Punching or blanking of the reduced section may produce significant cold asrm or shear burrs, or both, along the edges which should be removed by machining.

Extensometers shall be used and verified to include the strains corresponding to the yield strength and elongation at fracture if determined. E8M Tensiont testing of metallic materials Juliano row Enviado por: NOTE 1—The effect of this eccentric force application may be illustrated by calculating the bending moment and stress thus added.

A superscript epsilon indicates an editorial change since the last revision or reapproval.

ASTM E8.E8M -15-Tensiont testing of metallic materials

Any departure from this requirement may introduce bending stresses that are not included in the usual stress computation force divided by cross-sectional area. Astm c astm normas fibra de vidrio. The distance between spherical bearings should be as f8 as feasible.

Combining values from the two systems may result in non-conformance with the standard.