ASTM G36 PDF

Presented in this report are the results of stress corrosion cracking testing per ASTM G36 (Standard Practice for Performing Stress-Corrosion Cracking Tests in a. austenitic stainless steel was studied in accordance with the ASTM G The samples were unidirectional cold-rolled up to 60 and 90 percent reduction in. Revised ASTM G36 apparatus. This client had been testing stress corrosion- cracking in metal welds by clamping a QVF 2″ glass pipe fitting to his samples.

Author: Dolabar Kazrat
Country: Nepal
Language: English (Spanish)
Genre: Relationship
Published (Last): 9 April 2005
Pages: 290
PDF File Size: 4.80 Mb
ePub File Size: 17.83 Mb
ISBN: 412-5-27202-793-5
Downloads: 63105
Price: Free* [*Free Regsitration Required]
Uploader: Kehn

See Section 7 for specific safety precautions. The boiling points of aqueous magnesium chloride solutions at one atmosphere pressure as a function of concentration are shown graphically in Fig. The test specimens were immersed in the boiling solution and supported using the suggested ladder-back cradles.

Quality Assurance Return to Corrosion Testing. It is a method for detecting the effects of composition, heat treatment, surface finish, microstructure, and stress on the susceptibility of these materials to chloride stress corrosion cracking.

However, such correlations may not always be possible. On the finned test specimen, cracks extended down the fins from the outer edge to the tube wall in a direction roughly t36 to the tube wall; at the tube wall the cracks extended in a short arc both longitudinally and circumferentially, the arcs stopping before the next fin was encountered.

Active view current version of standard. Regular examination periods for test specimen cracking were scheduled. Test procedures conformed to the referenced ASTM test method.

t36

It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

Materials that normally provide acceptable resistance in hot chloride service may crack in this test. Cracking of both test specimens was observed, and the tests were terminated.

  AGOSTO CONDADO DE OSAGE PDF

Revised ASTM G36 apparatus

Circumferential cracking of the bare tube test specimen was g6 within the first 8 hours of testing even while the test specimen was on test. A suggested test apparatus capable of maintaining solution concentration and temperature within the prescribed limits for extended periods of time is also described herein.

Etching both sections did not reveal any additional crack depth as sometimes occurs in metallographic studies of stress-corrosion cracking. Deepest cracks found on transverse cross-section of finned tube. Link to Active This link will always route to the current Active version of the standard. Crack characteristics were investigated by preparing metallographic sections of the test specimens. See Section 7 for specific safety precautions. Although this test may be performed using various concentrations of magnesium chloride, this procedure covers a test solution held at a constant boiling temperature of Both test specimens were taken off test at 8 hours for examination at low magnification.

This leads to the possibility of confusing stress-corrosion failures with mechanical failures induced by corrosion-reduced net cross sections. The weld and HAZ of the finned tube appeared to have more cracks than the base metal, and the cracks appear to nearly connect from fin to fin. Circumferential cracks with connecting longitudinal crack in base metal of bare tube.

Corrosion Testing Laboratories, Inc. Newark, Delaware USA This danger is particularly great when small cross section samples, high applied stress levels, long exposure periods, stress-corrosion resistant alloys, or a combination thereof are being used. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Black lines indicate the approximate location of the outer surface of the tube. Accompanying paperwork states that both types of tube were fabricated from the same heat lot of material. Link to Active This link will always route to the current Active version of the standard. Return to Corrosion Testing. Photographs of typical appearance of the cracks on both tubes are shown in Figures 1 and 2. The boiling points of aqueous magnesium chloride solutions at one atmosphere pressure as a function of concentration are shown graphically in Fig.

  GAUSS DISQUISITIONES ARITHMETICAE ENGLISH PDF

It is a method for detecting the effects of composition, heat treatment, surface finish, microstructure, and stress on the susceptibility of these materials to chloride stress corrosion cracking. Two 2 1-foot long pieces of 0.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Referenced Aastm purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Historical Version s – view previous versions of standard. Deepest crack found on longitudinal cross-section of bare tube.

Although this test may be performed using various concentrations of magnesium chloride, this procedure covers a test solution held at a constant boiling temperature of No preparation other than deburring and degreasing was performed on aztm test specimens prior to testing. Careful examination is recommended for correct diagnosis of the cause of failure.

G2MT Laboratories

It was decided that cracks in wstm bare tube could be best examined using a longitudinal cross-section, while the cracks in the finned tube could be best examined using a transverse cross-section. Microphotographs of the deepest cracks found on the mounted sections are shown in Figures 3 and 4.

The test may not be relevant to stress-corrosion cracking in polythionic acid or caustic environments.

Posted in Art