ATMEGA328 TQFP PDF

The Atmel® picoPower® ATmega/P is a low-power CMOS 8-bit microcontroller 8-channel bit ADC in TQFP and QFN/MLF package. •. Temperature. Atmel high performance, low power 8-bit AVR ATmegaP-AU microcontroller in the TQFP package. Okay, so I’m about to blow up. I’ve tried to use perhaps 10 Atmega TQFP without any success.

Author: Zolohn Zuluramar
Country: Liberia
Language: English (Spanish)
Genre: Technology
Published (Last): 9 October 2004
Pages: 500
PDF File Size: 9.80 Mb
ePub File Size: 15.29 Mb
ISBN: 887-3-14609-894-7
Downloads: 46637
Price: Free* [*Free Regsitration Required]
Uploader: Shakashakar

ATmegaP Microcontroller – TQFP | ATmegaTQFP | Atmel

Have you applied power to the circuit? When programming through SPI, the chip accepts the program even if the fuses are set to accept clock signal from external clock. Ground yourself and use atmeag328 ESD mat. If all that is correct, there are a couple other things that could cause that error: Home Questions Tags Users Unanswered. If you have ever managed to program the fuses, the reset pin may have been disabled, or the device may be expecting an external crystal. It looks like the log text says ‘programmer operation not supported’, could be a symptom of bad cmd line args.

tsfp

If all that is correct, there are a couple other things that could cause that error:. TomCarpenter, the programmer does provide power. Check that the ISP header connects to the pins that it ought to, and check that you have the chip oriented correctly in the socket The USBtiny has a switch to power the target, so make sure that’s in the correct position.

  LEY ANTIMONOPOLIO ECUADOR PDF

I’m voting to close this question as off-topic because it has been abandoned for half a year in unanswerable state.

By using our site, you acknowledge that you have read and understand our Cookie PolicyPrivacy Policyand our Terms of Service. Atmega 2 9 Error while burning bootloader. Well atmega3328 of all, check the wiring.

The AVR programmer will not supply power.

ATMega328 – TQFP

Clearly I’m doing something incorrectly, and I wouldn’t doubt if it was because it’s not as simple as hooking the AVR programmer directly up to the chip to program it. Only HV programming does not. If this question can be reworded to fit the rules in the help centerplease edit the question. That is pretty much all you need.

ATmega328P Microcontroller – TQFP

The reset pin lacks the normal ESD protection, and so is fairly easy to fry. Can you edit the question to include the exact command-line arguments given to avrdude?

ISP requires a working clock source.

ATmegaP Chip Erase delay: Reset is driven by the programmer, and besides has an internal pullup. However, when attempting to upload the bootloader to the rqfp, I am presented with the following error:. It’s worth checking its in the correct position, though. Any help would be appreciated.

  HANDBOOK OF PERFORMABILITY ENGINEERING PDF

SCK serial program mode: Assuming your connection is incorrect, first you need to add a pull-up resistor to the reset pin; 1kk should be alright. Block Poll Page Polled Memory Type Mode Delay Size Indx Paged Size Size Pages MinW MaxW ReadBack eeprom 65 20 4 0 no 4 0 0xff 0xff flash 65 6 0 yes 0xff 0xff lfuse 0 0 0 0 no 1 0 0 0x00 0x00 hfuse 0 0 0 0 no 1 0 0 0x00 0x00 efuse 0 0 0 0 no 1 0 0 0x00 0x00 lock 0 0 0 0 no 1 0 0 0x00 0x00 calibration 0 0 0 0 no 1 0 0 0 0 0x00 0x00 signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00 Programmer Type: If the reset pin has been disabled, you’ll need a special high voltage 12V programmer to recover it.

Crystal requirement comes when booting through the bootloader i. Atmdga328 SCK period of 10 usec avrdude: This question does not appear to be about electronics design within the scope defined in the help center.

I’ve simply connected the AVR programmer to the chip in the adapter socket as follows AVR connector on left, chip on right.