View and Download Bosch VMD01 M50 PAL operating instructions manual online. Security Sensors Bosch DMF 10 Zoom Operating Instructions Manual. Related Manuals for Bosch VMD01 M50 PAL. Security Sensors Bosch DMF 10 Zoom Operating Instructions Manual. Digital detector ( pages).
|Published (Last):||9 October 2018|
|PDF File Size:||20.5 Mb|
|ePub File Size:||8.81 Mb|
|Price:||Free* [*Free Regsitration Required]|
Position the measuring tool onto the surface to be scanned and move it sidewards.
The signal tone setting is maintained after switching the measuring tool off and on again. To localise the object precisely, press the “ZOOM” button 4 and keep it pressed while repeatedly 3x moving the measuring tool over the object.
Bosch VMD01 M50 PAL Operating Instructions Manual: Funktionen
Observe only the zoom measuring indicator e for the scan. Only for EC countries: When the measuring tool is in the metal-detection function, the service readiness is indicated through a check mark behind the “AutoCal” calibration indicator g. Marking Objects Detected objects can be marked as required. Main page Brands Categories Search. Operating Modes The measuring tool detects objects below the sensor area 9.
GMS M Professional , Detector | Bosch
Position the measuring bedienungsaanleitung onto the surface being scanned. Detecting Wooden Aoom When scanning for wooden objects, press the wood-detection button 5. When the calibration process was successful, the measuring tool will start over after a few seconds and is then ready for operation. We hope, that this document of instructions for use will help you. Initial Operation Protect the measuring tool against moisture and direct sun irradiation.
For non-magnetic metals, the indicator for non-magnetic metals i is displayed.
Detecting Metal Objects When scanning for metal objects, press the metal-detection button 6. Si el tiempo de almacenaje es prolongado, la pila se puede llegar a corroer o autodescargar. To distinguish between wooden and metal objects, switch bosh the detecting-metal function see “Detecting Metal Objects”.
Deposite el aparato de medida sobre la superficie a explorar.
BOSCH DMF 10 ZOOM others download manual for free now – 29A3E |
As long as the measuring tool is above the metal dkf, the illuminated ring 1 lights up red and a steady tone sounds. Move the measuring tool over the surface repeatedly to localise the wooden object more precisely. For steel wire mesh, it is typical that zlom indicator for magnetic metals h becienungsanleitung displayed directly above the rebar; the indicator for non-magnetic metals i is displayed between the rebars. Intended Use The measuring tool is intended for the detection of metals ferrous and non-ferrous metals, e.
Then press the “ZOOM” button 4 and keep it pressed. During the scan, the felt pads 8 must always have contact with the structure. Pay attention that the polarity is correct, according to the representation on the inside of the battery lid.
All information such as file size, preview picture, category manual, model and more, you can find below.
Blinkt die Anzeige k, dann sind noch ca. When the signal tone is switched bedienngsanleitung, the switched-off audio signal indicator j appears on the display.
DMF 10 Zoom PROFESSIONAL
In this case, always use the “Zoom” function for the scan. After downloading the file, save it in safe place for example in “My documents” or “Desktop” folder.
For this, remove all objects in the vicinity of the measuring tool including wrist watches or rings of metal and hold the measuring tool up in the air. If required, wipe the measuring tool dry using a cloth. Litzenkabel werden dabei nicht angezeigt im Gegensatz zu Vollmaterialkabeln. For this, press the metaldetection button 6 and the wood-detection button 5 at the same time.
However, stranded cables are not indicated contrary to solid copper conductors. When the battery indication k in the display lights up, measuring is possible for approx.
Once you have found the limits or the centre of an object, simply mark the sought after location through the marking opening 2. Initial Operation Protect the measuring tool against moisture and direct sun irradiation. Reiben Sie das Messwerkzeug gegebenenfalls mit einem Tuch trocken.
As long as the measuring tool is above the metal object, the illuminated ring 1 lights up red and a steady tone sounds. Para conectar el aparato de medida pulsar una tecla cualquiera. Intended Use The measuring tool is intended for the detection of metals ferrous and non-ferrous metals, e. For steel wire mesh, it is typical that the indicator for magnetic metals h is displayed directly above the rebar; the indicator for non-magnetic metals i is displayed between the rebars.
Wischen Sie Verschmutzungen mit einem trockenen, weichen Tuch ab. Therefore, please also observe other information sources e. When the battery indication k flashes, measuring is still possible for approx.
Lassen Sie dann beide Tasten los. In this case, send in the measuring tool to an authorised Bosch after-sales service agent. Marking Objects Detected objects can be marked as required.
In this case, send in the measuring tool to an authorised Bosch after-sales service agent. Observe only the “Zoom” measuring indicator e for the scan.
Once you have found the limits or the centre of an object, simply mark the sought after location through the marking opening 2. The “Zoom” measuring indicator e is inactive when scanning for wooden objects.