The DSB is a serial port to 1-Wire interface chip that supports standard and DSB uses a unique protocol that merges data and control information. Maxim Integrated DSB Series Buffers & Line Drivers are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for Maxim. OneWire library custom engineered for JLD boards with DSB chips – collin80/DSB.
|Country:||Central African Republic|
|Published (Last):||12 November 2011|
|PDF File Size:||19.97 Mb|
|ePub File Size:||14.53 Mb|
|Price:||Free* [*Free Regsitration Required]|
Note that this number is a conservative estimate. The ds248b0 at which a cs2480b slave recognizes a time slot depends on three factors: The recharging duration of Phase 1 is calculated using equation 3. For requests to copy this content, contact us. Part Number Replacement Explanation. To run the program, double-click its icon or right click the icon and select “open. Consequently, anything that affects the process of charging and discharging the network is a parameter that must be considered when determining the driver performance.
Sorry, but we are unable to process sample requests from non-business or non-educational e-mail addresses via this site. This is true because: What application are you planning to use this part for? Crossing this threshold starts vs2480b timer that must expire before the active pullup is turned off.
Visit My Quotes Thank you! Nonetheless, the robustness of the communication will suffer, resulting in retries that appear as a slower response or in reduced throughput. Communications Wireless and RF. After completing the above calculations, the resulting number of slaves for flexible speed is Click here to purchase parts.
Unfortunately, we are unable to place your order due to restrictions on your account. Command codes received from the host’s crystal controlled UART serve as a reference to continuously calibrate the on-chip timing generator.
When the 1-Wire line is idle, the DSB driver performs the pullup through a controlled current source. The third appendix discusses network overload conditions. This approach maintains compatibility to off-the-shelf serial to wireless converters, allowing easy realization of 1-Wire media jumpers.
As illustrated in Figure 2the Write 1 and Read Data time slots are constructed from three segments: Consequently, at overdrive speed the DSB driver is at least four times as strong as the 2. The slave’s low capacitance applies. The slaves tolerate incomplete recharge as long as the voltage rises high enough to be recognized as the end of the time slot.
DSB Serial to 1-Wire Line Driver – Maxim
If the recharge starts later, there is less energy needed to recharge; the duration of Phase 1 is shorter, leaving more time for Phase 3 to compensate. A 1-Wire slave does not behave like an ideal ds2480v.
Consequently, at standard speed the DSB driver is at least six and a half times as strong as the 2. What project s will these Maxim parts be used in?
The function of Q2 is not discussed in this application note. DSB, DS, 1-wire,1wire, timing, configure, configuring, time slots, waveforms, parameters, slew rate, pulldown, dx2480b 1, write 0, UART, tmline, timline.
Understanding and Configuring the 1-Wire Timing of the DS2480B
IO-Link and Binary Drivers. Please contact customer support.
See Application Note Please provide as much detail as possible in your answers. MyMaxim My Maxim logout. Alternatively, you can click here to place an order. This document discusses the configurability and performance dss2480b the DSB.
Implementing an Isolated 1-Wire Bus. The number to be entered is the parameter value code, found in Table A. Functional General Analog Input. With a slew-rate setting of 1. The actual achievable number of slaves could be significantly higher.
However, a consequence of adding R T is that the active pullup can turn off prematurely before the 1-Wire line is fully recharged at the ds24800b device s.
To speed the recharge process, the DSB uses a 2-stage current source instead of a resistor. Add different End Customer. For Phase 3, calculate the residual time available for recharge, and use equation 1 to determine the additional voltage increment that can be achieved with I WEAKPU.
The parameter values in Table 5 were used to calculate the result. Phase 1 Recharge from 0 to 3.