GY520 MANUAL PDF

Futaba GY Pdf User Manuals. View online or download Futaba GY Instruction Manual. Nstruction, Anual • Read online or download PDF • Futaba GY User Manual. The chart below works for almost all helicopters but you should consult your helicopter manual if you are not sure. Note that I have seen.

Author: Kazrazragore Mazugor
Country: Sudan
Language: English (Spanish)
Genre: Finance
Published (Last): 23 December 2009
Pages: 440
PDF File Size: 17.84 Mb
ePub File Size: 3.48 Mb
ISBN: 377-6-88963-362-2
Downloads: 29468
Price: Free* [*Free Regsitration Required]
Uploader: Moogujar

Because this is on a small heli and I wanted to keep the wiring short I made my own. It is great they did this so you do not get mixed up.

To maanual the tail to move faster or slower, adjust the rudder channel travel. Standard Rate mode Move the Gear switch down position 1.

Futaba GY520 Helicopter Gyro w/Heading Hold

That is the servo limit setting mode. My setup on the miniTitan is Gy250 next second it will blink fast. The gyro will repeat a ‘1 blink’. It also depends on how the link connects to the servo. When you connect the servo plug to the gyro you need the link to be off so it does not bind.

Hold the button on the gyro for 2 seconds to go to the next function. In order to be able to post messages on the HeliFreak forums, you must first register. In the picture, Aux2 is set to INH but this does not matter for this gyro setup.

  LIBRO SOLFEO DE LOS SOLFEOS PDF

Futaba GY Manuals

If you see the tail wag then lower the gain. You will see the servo move to one side. This will save the setting. You should make the decision based on what your flying style is. One direction will set the gain value for heading hold and the manuao will be for standard rate.

At this time we need to check that the radio is correctly controlling the gyro. Most other receivers have it labeled channel 5. The light on the gyro will do a 4-Blink. A high framerate setting on a low framerate servo will damage the servo in a minute. On a larger class 50 size it might be in the 80 to range.

Snap the link on the servo and check that you do not get binding at full left and full right. If not, hold the button down to enter setup mode. You may want it faster or slower so change the value appropiately.

Do not tie the soft rubber line down to the helicopter, close to the gyro. Check the holes in the arm for one that is 90 degrees to the tail control rod.

Hold the button down again for 3 seconds to get to the next function. From the servo limit function, hold the gyro button down for 2 seconds to get to the Flight Mode selection. This will set it up for the next step.

Use a marker to write on the label ‘R’, ‘G’, and ‘S’ as shown in the bottom picture to the left. Hold in the button on the gyro for three seconds. Note the color of this light.

  CONDENADOS A VIVIR JOSE MARIA GIRONELLA PDF

FUTABA GY520 Instruction Manual Page 23

Janual rotated the servo mount to a position that put the ball directly inline with the tail control rod. In the picture on the left you see I am not using them. Note that I have seen common problems with the tail blades grips flipped the wrong direction and the tail belt twisted the wrong direction. This tells the radio that you want to control the Gear channel of the receiver by using the switch on the radio that is labeled Gear.

Use the ‘clear’ button to set the values to zero. There is an error in the instructions which has been corrected on Futaba’s FAQ page. If not then go back to step 1 vy520 start again. Thank you so much! Place the servo arm on the servo spline. There are three things that need to be connected. Hold the gyro button in for 2 seconds to get to the 5-Blink mode. Remove Advertisements Sponsored Links. The tail servo will connect to the side that has one socket.

I fly smooth 3D and prefer the slower rotation rate. Now power off the receiver and plug the tail servo up to the gyro.