HCNW3120 DATASHEET PDF

HCNW datasheet, HCNW pdf, HCNW data sheet, datasheet, data sheet, pdf, Agilent (Hewlett-Packard), Amp Output Current IGBT Gate Drive. Broadcom HCNW available from 7 distributors. Explore Optoelectronics on Octopart: the fastest source for datasheets, pricing, specs and availability. HCNW datasheet, HCNW circuit, HCNW data sheet: HP – Amp Output Current IGBT Gate Drive Optocoupler,alldatasheet, datasheet.

Author: Tojagal Mushakar
Country: Croatia
Language: English (Spanish)
Genre: Photos
Published (Last): 3 December 2007
Pages: 229
PDF File Size: 7.31 Mb
ePub File Size: 12.69 Mb
ISBN: 953-8-55715-430-9
Downloads: 44442
Price: Free* [*Free Regsitration Required]
Uploader: Sabei

HCNW Datasheet(PDF) – Agilent(Hewlett-Packard)

The high operating voltage range of the output stage provides the drive voltages required by gate controlled devices. Pins 1 and 4 need to be connected to LED common. However, once mounted on a printed circuit board, minimum creepage and clearance requirements must be met as specified for individual equipment standards. Dead time is the time period during which both the high and low side power transistors Q1 and Q2 in Figure 25 are off. However, this shield does not eliminate the capacitive coupling between the LED and optocoupler pins 5—8 as shown in Figure The LED is optically coupled to an integrated circuit with a power output stage.

These dimensions are needed as a starting point for the equipment designer when determining the circuit insulation requirements.

Delaying the LED signal by the hcnw310 propagation delay difference ensures that the minimum dead time is zero, but it does not tell a designer what the maximum dead time will be. To order, choose a part number from the part number column and combine with the desired option from the option column to form an order entry. This capacitive coupling causes perturbations in the LED current during common mode transients and becomes the major source of CMR failures for a shielded optocoupler.

  COMPOSTEIRA DOMESTICA PDF

Temperature Figure 3 VOH vs.

Figure 33 is an alternative drive circuit which, like the recommended application circuit Figure 25does achieve ultra high CMR performance by shunting the LED in the off state. Contact your Avago Technologies sales representative or authorized distributor for information.

Contact an Avago Technologies sales representative or authorized distributor. In this test, VOH is measured with a dc load current.

HCNW3120 Datasheet PDF

This is achieved by overdriving the LED current beyond the input threshold so that it is not pulled below the threshold during a transient. There are recommended techniques such as grooves and ribs which may be used on a printed circuit board to achieve desired creepage and clearances. Dtasheet to keep the LED in the proper state are discussed in the next two sections. Device considered a two-terminal device: Data subject to change.

For the continuous voltage rating refer to your equipment level safety specification or Broadcom Ltd. See Applications section for additional details on limiting IOH peak. To minimize dead time in a given design, the turn on of LED2 should be delayed relative to the turn off of LED1 so that under worst-case conditions, transistor Q1 has just turned off when transistor Q2 turns on, as shown in Figure This results in lower peak currents more margin than predicted by this analysis.

  CCNA VOICE STUDY MATERIAL PDF

Note that the propagation delays used to calculate PDD and dead time are taken at equal temperatures and test conditions since the optocouplers under consideration are typically mounted in close proximity to each other and are switching identical IGBTs. Maintenance of the safety data shall be ensured by means of protective circuits. Lab 9 in this note.

For creepage, the shortest distance path along the surface of a printed circuit board between the solder fillets of the input and output leads hcn3120 be considered. Any overlap in Q1 and Q2 conduction will result in large currents flowing through the dahasheet devices between the high and low voltage motor rails. Option data sheets are available. AVEN — March 21, The thermal resistance values given in this model can be used to calculate the temperatures at each node for a given operating condition.

All other brand and product names may be trademarks of their respective companies. When negative gate drive is not used VEE in the previous equation is equal to zero volts. Creepage and clearance distances will also change depending on factors such as pollution degree and insulation level. The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous voltage rating.

Minimum External Tracking L Creepage 7.