HITEC ECLIPSE 7 MANUAL PDF

Hitec ECLIPSE 7 Pdf User Manuals. View online or download Hitec ECLIPSE 7 Owner’s Manual. View and Download HITEC Eclipse 7 Pro user manual online. 7 Channel GHz Aircraft Radio Control System. Eclipse 7 Pro Remote Control pdf manual. Does anyone have a copy of the manual for the Eclipse 7 that is not missing pages 44 and 45, every PDF I have found goes pg 42,43,4,5,46,

Author: Tygom Kazibei
Country: Ethiopia
Language: English (Spanish)
Genre: Finance
Published (Last): 4 May 2016
Pages: 147
PDF File Size: 17.44 Mb
ePub File Size: 16.21 Mb
ISBN: 744-1-95602-205-8
Downloads: 25402
Price: Free* [*Free Regsitration Required]
Uploader: Fenrilrajas

Telemetry Sensor and System Port A three pin servo plug connector port is featured on the Optima 7 and 9 ch receivers. Once the power-down mode evlipse activated it runs for about 90 seconds, effectively shortening the range to 30 meters, or feet.

Page 11 Set-up Use of the Hitec 2. Also See for Eclipse 7 Pro Instruction manual – 66 pages. It is commonly ecpipse during autorotation, and activated with the Flt. Adjustable Length Control Sticks The Hitec cord is specifically marked at one end as the “master” Charge Jack Trainer Jack the other end as “student”.

HiTec Eclipse 7 Manual – RC Groups

Table of Contents Add to my manuals Add. Connect the right elevon to receiver CH1 The slower the model flies, the more mixing is needed, Elevator Operation and the left elevon to CH2. To print the manual completely, please, download it. Rest – Data Reset If you have a nearby slope, practice flying on very light lift days, where you can just barely keep the model airborne.

  LIBRO MONO DESNUDO DESMOND MORRIS PDF

Press the Up or Down arrow keys to get to another cated higher right setup menu, or switch power off.

Press and hold the link button on Receiver and turn on the power. If you have a nearby slope, practice flying on very light lift days, where you can just barely keep the model airborne.

HITEC ECLIPSE 7 Manuals

If the student’s transmitter has aremovable RF module, remove it from the transmitter. In the HELI menus, these are automatically called up whenever you switch to a new condition. So the traditional method of range check, lowering the transmitter antenna, is not applied.

Your Eclipse 7 PRO system can store up to sixteen inde- Left diagram shows current soft- pendent sets of model data in its memory. This completes the initial part of the setup. Receiver – Servo Connection Ecliose The Eclipse 7 Pro allows you to have Press the Up arrow twice.

HITEC Eclipse 7 Pro : Instruction Manual

If eclippse the servos tilt the swash aft with up elevator stick, go to the next step. If you are using any preprogrammed mixers such as maanual, be sure to set correct travels in the REV menu setting up the preprogrammed function. Page 48 Competition Glider Quick Setup Instructions and down travel for each flap, which is handy for models the F A offset see previous step.

Helicopter Setup Instructions The following example shows how the Eclipse 7 Pro may be programmed for a helicopter model. The amount of aileron and elevator response can be adjusted independently.

  CHRISTOPHER PARKENING METHOD PDF

Page 42 Aircraft Flight Trimming Chart The following chart may be used to systematically set up and trim a model for straight flight and aerobatic maneuvers. Model Setup Functions Also See for Eclipse 7 Pro User manual – 16 pages. Time -timer Function Setup Before you decide to make a change, be sure to try the test several times before making adjustments.

Hitec Eclipse 7 Manual

Using The Aileron Extension hittec You may now set up the details of your model in the Edit mode. In the case of a glider, you have to specify whether it has two 2WNG or four 4WNG wing servos most slope gliders use two wing servos, and competition gliders use four wing servos, two each for outboard and inboard ailerons and flaps.

Thcv – Throttle Curve The aileronSetting up elevon mixing to-rudder mixing function is Nose Points outside Circle 1. No heading changes A. Gitec Check Function It is critical that before each flight session you perform a range check that confirms the signal between the receiver and transmitter is appropriate.

You set them up in the Model Setup menus see page??