6(&. iC-v SERVICE. MANUAL DISASSEMBLY INSTRUCTIONS. SECTION 4 . Specified Icom’s battery pack only (Operating voltage range; – V). View and Download Icom IC-V82 instruction manual online. Icom America VHF Transceiver, VHF Transceiver Instructions Manual. IC-V82 Transceiver pdf. View and Download Icom IC-V82 instruction manual online. VHF TRANSCEIVER . IC-V82 Transceiver pdf manual download.
|Published (Last):||11 August 2012|
|PDF File Size:||2.9 Mb|
|ePub File Size:||17.39 Mb|
|Price:||Free* [*Free Regsitration Required]|
Microphone simple mode is used to change the function as- signments for keys in the optional HMA as below. You can wait for calls from group members using the same tone and not hear other signals. The digital code or call sign squelch does not function while in a low- speed data communication.
This manual also for: In the EMR communication mode, no call sign set- ting is necessary. Each mem- ory channel, 0 tomay be assigned to one of the banks for easy memory management.
IC-V82, IC-U82 Downloads
Only tested and approved for use with genuine Icom bat- teries. Page 95 We Icom Inc. When this setting is set to ON, the transceiver automatically indicates your programmed call sign manuap turning power ON or digital mode transmission.
When receiving signals, the scan pauses according to the scan pause time. This system provides you with much wider coverage range during digital voice mode operation. The offset and repeater tone is not changed by the auto repeater function. Each receive and transmit frequency is shown in the table below with mahual following conditions; IC-V82 Input frequency: The offset and repeater tone frequencies are not changed by the auto repeater function. Call sign notes are coupled with the same channel number of your own call signs, and they are ic–v82 or indicated after your own call signs.
Icom IC-U82 User Manual | 96 pages | Also for: IC-V82
D D Your call sign note programming You can add information to iicom own call sign such as oper- ating radio type or area. VFO mode and memory mode. This setting can be set for each memory, call and VFO inde- pendently. Up to 6 transmit codes codes that you transmit are pro- grammable into code channels, C1 to C6, if required.
Some options may not be available in some countries. If this problem occurs, turn power OFF. Scan Resume Condition D Memory scan watch While operating on a VFO frequency, memory scan watch monitors for signals in each memory channel in sequence, every 5 sec. This setting allows you to set a minimum signal level needs to open the squelch. Page of 96 Go. Each of these channels can be individually programmed with op- erating frequency pgs.
IC-V82, IC-U82 Downloads – Icom America
Program them in the same manner as regular memory channels. Pager selective code push [PTT] Answer back manual Set both transceivers to either code squelch or non-coded operation When the display type setting pgs.
Transmit frequency shifts in normal duplex mode. Setting frequency In VFO mode, set the desired operating frequency with other desired settings, such as repeater and subaudible tone. Page 47 D Setting subaudible tones for tone squelch operation Separate tone frequencies can be select for tone squelch op- eration rather than repeater operation the same range of tones is available— see right below.
See next set of instructions for setting tuning step size. When the reversed duplex mode is selected, the receive fre- quency shifts. D Setting subaudible tones for tone squelch operation Separate tone frequencies can be select for tone squelch op- eration rather than repeater operation the same range of tones is available— see right below.
Attach the belt clip with the supplied screws using a phillips screwdriver. The previously selected used weather channel is checked periodically during standby or while scan- ning. Repeater Operation When the reversed duplex mode is selected, the receive fre- quency shifts.
Don’t show me this message again.
Even if the memory bank contents are cleared, the memory channel contents still remain pro- grammed. Please ask your dealer for details. The following items are additionally required. The ic-82 data can also be transmitted with a message to another station.
The display type is selected in p.
ICOM IC-V82 User Manual
Transmit at 7 W High at 4 W Middle 2. Repeater Operation Direct frequency input from the key- pad is also available.
The following are additionally required: Iic-v82 of codes are available. DTMF memories are used to store phone numbers or control codes. To print the manual completely, please, download it. Code Squelch [PTT] to receive. Reset these frequencies, if necessary. Don’t have an account? Page 55 D D Your call sign note programming You can add information to your own call sign such as oper- ating radio type or area.
Table of Contents Add to my manuals Add. Operation manuql sub- ject to the following two conditions: Page 94 We Icom Inc. To provide the recipients of your