JTAG PANTEC PDF

Pantech Solutions. Online Retail store for Trainer Kits,Lab equipment’s,Electronic components,Sensors and open source hardware. This process is to assist in the repair of your Pantec receiver. There are 2 We need to Build a JTAG cable and we need to modify the receiver. To modify the. have performed the JTAG operation on my Pansat A using both Skymax and jKeys .. The first thing to do here is figure out if you have a PanTec MX or MS.

Author: Kagahn Gall
Country: Solomon Islands
Language: English (Spanish)
Genre: Finance
Published (Last): 17 February 2007
Pages: 129
PDF File Size: 3.77 Mb
ePub File Size: 5.91 Mb
ISBN: 501-4-51534-547-2
Downloads: 42645
Price: Free* [*Free Regsitration Required]
Uploader: Vumuro

Use CPU double sided heat tape. Now turn on the receiver and look at the front of mtag unit. Network Analysis Tools The process window will appear. Go slowly and be gentle. This is for the MS. Don’t forget the rear panel screw near the RCA plugs.

I would let this run for a few minutes. How does cache work? Lab3 SD card Audio Player: The cathode of the LED to the anode of the 1N The receiver should be switched off but plugged in. Download the file to the receiver and wait until complete. Allow the process to complete. The next step is to flash the receiver using the serial cable that panrec with your receiver and the Pansat Loader v3.

If the receiver lights up then all is well. Gently rest the resister end on top of one solder pad on the board. The 5 resister bank shown below will be missing the 4th resister.

  EDGAR ALLAN POE EL CORAZON DELATOR PDF

You will have to off set the fan to jtxg the caps. Configure the Camera and Related Modules Step 5: Try not to move the resister pantef at all after soldering. The rest of the wires are your data lines. Microchip uses the pin arrangement illustrated below on those development boards, such as the Explorer 16 Development Boardthat are JTAG enabled.

Pantec FTA Files & Pantec FTA KEYS

Do not use a soldering gun. Take a heat sink and fan. Plug in the receiver but keep the power switch off. Put a very small amount of solder on the ends of the wire.

Remove the corner screw and place the header board on top then put the screw through the perf board and re tighten it. Now confirm all connections and make sure you haven’t left anything inside the unit that could short.

Do not attempt to drill new holes. Gently remove the receiver board from the case. Measure the distance with the LED’s and drill 4 holes in the plastic box that will line up to the position of the LED’s on the perf board.

Which jtag is best for pantec mx

If you want to discuss contents of this page – this is the easiest way to do it. The Receiver has to be modified and woken up. Bend the leads so the parts won’t fall out but don’t solder jtga yet. Panfec the JTAG cable to your computer parallel port and then plug in the 10 pin connector to the receiver. Note the IRD number is the order in the list Click the pull down tab and select it.

  BINUTILS GAS PDF

The new Bin you want to load. Solder one end of the resister from this point. The traces will lift and or melt if heated too much. This isn’t absolutely necessary but a good idea. Turn off the receiver and disconect the JTAG cable and replace the cover and the 5 screws.

If you experience problems with DCU errors in Jkeys, this will probably solve it.

Reconfiguring existing project Step 4: Turn on the receiver. Generate Harmony Code Step 6: Feel the heat from the unit and see how hot it gets.

For this step of the procedure, you will need some software. Don’t touch anything until the completed box appears.

Make sure the unit is unplugged, remove the power connector plug from the receiver board. Pin Mapping Htag 2: Lab1 SD card Audio Player: Analog Sensor Conditioning Additional content planned