LENZE 8600 MANUAL PDF

View and Download Lenze series operating instructions manual online. Inverter Drives Variant Dancer-position control with Torque control. series. vector. System/Component overview. Lenze. FU vector en 11/ 3. System overview/Selection guide. Communication modules e.g. keypad or. PROFIBUS. Get Lenze IB Manual. Get all Lenze manuals! with optical fibre cable together with the controller series as of E DC controller E 5x. 6x.

Author: Kezragore Balkis
Country: Turkmenistan
Language: English (Spanish)
Genre: Video
Published (Last): 13 June 2005
Pages: 370
PDF File Size: 19.12 Mb
ePub File Size: 20.91 Mb
ISBN: 859-7-47807-851-6
Downloads: 25857
Price: Free* [*Free Regsitration Required]
Uploader: Shakakora

Minimum field You tan use Code CO10 to program a minimum output frequency. To switch the Signal cables, only use relays with low- current contacts. Code table The following table Shows which settings you tan enter under which Codes. Application-specific Controller Selection Here you have to distinguish whether the control system e.

This function is necessary to avoid an unintended starting of the drive during switch on. Page 3 How to use these operating instructions The second byte is not used and must have a 0. Speed deceleration hex The parameter “speed deceleration” corresponds to the absolute speed ramp of the deceleration. Loop Control With Speed Adaption 9. Page 4 Safety information The equipment described is intended for use in industrial drive systems.

Lenze – : DACPOL-SERVICE

Input Of Correction Value In this configuration, only one motor tan be connected. Page – Signal flow Chart for dancer-Position co Page 23 Programming The programming section using the IB bus interface module is divided into the following chapters: Burst of 4kV on the power terminals and 2kV on the control terminals are permissible.

  ANDEX CHART 2009 PDF

Page 8 6 L Page 9 Planning 1. Unwinding 860 above or from below For unwinding, the sign for the influence of the dancer-Position Controller must be inverted.

The permissible continuous output powes rises the same way. How to use these operating instructions Diameter And Radius Detection As standard, you can connect a maximum of 32 participants including hosts to the RS bus.

More detailed information about the use of the manjal can be obtained from the chapter “process data configuration” page The RFI filter must always be connected to earth at first even if manuxl only want to test the Otherwise, the System is not protected against shock.

I Controller Enable Page – Gain adjustment – radius Signal Page – Maual of the radius calculation Page – Adjustment of the dancer-Position contro Additional Acceleration And Deceleration Times Winding Or Unwinding Page 45 Parameter value or fault information in case of an invalid access.

Either the value or a fault indication is output. These Operating Instructions are valid for the units with the following nameplate data: Page 7 4 Closed-loop speed control 4. Technical Data Of Rfi Filters Initiate The initiate service is used for the logic initiation between two participants.

  BHARATHIAR UNIVERSITY CPOP MCA SYLLABUS PDF

All control inputs and Outputs of the controller are mains- isolated. Page 84 – Functions of the freely assignable digit The profile numbers Fhex to hex are not available any more.

This is shown in the following. 6800 these you tan select each one for control and programming.

Configuration – Lenze EDS4900U-REG User Manual

If you want to set the controller locally, proceed just like in the operating mode mixed operation. The parameter is mapped via the ramp-min function to the Lenze deceleration ramp L-C Irrstall the sine filter as close as possibie to the controller.

Operation with DC-bus supply 5. Typ I16 Bhex 2 I16 4. Or point us to the URL where the manual is located. Index hex Sub- Data index str. DP parameter setting channel For the DP parameter setting channel, parameter setting and diagnosis is possible in the user data operation.